Wall

C-DIAL

The C-Dial is a compact control unit, easy to operate, making it perfect for small residential applications. It can control up to 6 solenoid valves with 2 programs and 2 starts each. The practical 3 Easy Steps programming allows irrigation to be adjusted in just 60 seconds.

Controller type: Wall-mounted
Models available:
- 4 and 6 zones
Power supply: External transformer 220 VAC 50-60 Hz - 24 Volts AC, 0.8 AMP
Programming mode:
- Traditional

Instructions

Request information

Technical information

Technical features

Controller type: Wall-mounted
Power supply: External transformer 220 VAC 50-60 Hz - 24 Volts AC, 0.8 AMP
Back-up battery: 2 alkaline batteries 1.5 volts (AA) not included
Rain sensor input
Pump/master valve control outlet
Closing lid
Low battery signal
Maximum number of zones: 6
Models available:
- 4 and 6 zones

Standard Programming

Programming mode:
- Traditional
Number of programs: 2
Start times per program: 2
Maximum number of starts per day: 4
Minimum irrigation time per zone: 1 min
Maximum irrigation time per zone: 240 min
Irrigation frequency:
- By days of the week
Manual start:
- By zone
Reset button
Clear key

Advanced programming

OFF function:
- Control unit
Seasonal adjustment from 10% to 200%

3 Easy Steps

The special three-step programming feature allows for easy and intuitive programming in less than 60 seconds. The programming logic is based on answering three simple questions: what time of day to water, for how long, and how often.

Sensor input

The controller is equipped with a sensor input for the connection of the rain sensor, 2 wired normally closed. Installation of the rain sensor prevents irrigation during rain events thus saving water.

24 Vac Solenoid

The controllers control 24 Vac normally closed solenoids. The control unit will supply the solenoid with a 24 Vac electrical signal for the entire irrigation time to open the electrovalve.

	Code	Description	Barcode	Sales channel
	200.4180410	Centralina da parete C-DIAL 4 - 4 ZONE	8058054002763	Pro, Retail
	200.4180610	Centralina da parete C-DIAL 6 - 6 ZONE	8058054002770	Pro, Retail

	Code	Description	Barcode
TRS 220V/24 VAC		External transformer compatible with C-Dial and I-Dial control unit models

C-DIAL & I-DIAL

Difference between Programs and Zones.

Controllers programs identify an area or group of solenoid valves. Zones identify a specific solenoid valve.

How do I set the start time of the zones?

Irrigation controller programming is based on irrigation cycles distributed over irrigation programs, which means that it is not necessary to set the start time for all zones. It is sufficient to set the start time of the irrigation cycle (program start time) and the irrigation times of the zones. The controller will then open and close the solenoid valves in sequence.

I have programmed the I-Dial or C-Dial controller but it never irrigates.

The days of the week were probably not enabled during programming. Check that the days of the week in the frequency menu are enabled (frame around the day). If they are not active simply press the "+" key to enable the flashing day and move between days of the week with the "enter" key.

The screen shows the umbrella symbol but it did not rain

Verificare che il sensore pioggia a due fili sia correttamente installato e sia un sensore pioggia normalmente chiuso (modello Acqua Click). Se il sensore pioggia non è presente, verificare che il ponte di metallo nel vano morsettiera in corrispondenza della scritta "SENS" sia presente. In caso di centralina I-DIAL OUTDOOR verificare che il collegamento alla rete elettrica 220V sia stato effettuato correttamente (questa operazione necessita di un elettricista abilitato) e che non sia stato installato un trasformatore esterno 220/24 VAC.

Can I enable the rain sensor for single zones?

It's not possible to activate the rain sensor per zone with C-Dial. It's possible to activate the rain sensor per zone from the EXTRA functions with I-Dial.

Can I enable the rain sensor for single zones?

It's not possible to activate the rain sensor per zone with C-Dial. It's possible to activate the rain sensor per zone from the EXTRA functions with I-Dial.

I noticed that when irrigation starts, the irrigation cycles are repeated twice in a row. How can I set only one daily cycle?

Check whether 2 start times or 2 programmes are active

The control unit is properly powered but the screen indicates NoAC.

NoAC indicates that the circuit board is not receiving 24VAC. This situation can occur when the fuse is blown or the power supply is blown.

C-Dial - Instructions and programming

Discover now: C-DIAL for irrigation systems and transform your garden into a green oasis!